50/50 Setup Template

1 Replies, 9850 Views

Chassis introduction: (Tell everyone about your chassis)

RC Drift Chassis Information
Manufacturer:
Model:
Track Surface:
Tires:
Motor and ESC:
Servo:

Chassis Settings
Front Setup
Camber (Degrees) (Positive is out, Negative is in):
Toe (Degrees) (Specify Toe in or out):
Caster (Degrees):
Kick-up (mm):
Sway Bar (yes/no):
Ride Height (mm):
Springs (indicate type, length, hardness, etc):
Damper Oil (indicate weight or #):
Upper Damper Position (Lower # indicates inner most position):
Lower Damper Position (Lower # indicates inner most position):
Other (Weights, Mods, etc):

Rear Setup
Camber (Degrees) (Positive is out, Negative is in):
Toe (Degrees) (Specify Toe in or out):
Caster (Degrees):
Kick-up (mm):
Sway Bar (yes/no):
Ride Height (mm):
Springs (indicate type, length, hardness, etc):
Damper Oil (indicate weight or #):
Upper Damper Position (Lower # indicates inner most position):
Lower Damper Position (Lower # indicates inner most position):
Other (Weights, Mods, etc):

Drivetrain (Optional)
Front Belt (mm or teeth):
Rear Belt (mm or teeth):
Front Pulley (teeth and differential type):
Front Center Pulley (teeth and differential type):
Rear Center Pulley (teeth and differential type):
Rear Pulley (teeth and differential type):

Gearing
Spur (teeth and pitch):
Pinion (teeth and pitch):
[Image: dmsig02.jpg]
RC Drift Chassis Information

Manufacturer:MST

Model:MS-01D Pro

Track Surface: Rough Asphalt/Cracked driveway/ clay tennis court

Tires:Raikou D70, MST kit set

Motor and ESC:Flux vapor system 5900 kv

Servo:Spektrum S6040 (borrowed, getting rc omg bf or cf soon)



Chassis Settings

Front Setup

Camber (Degrees) (Positive is out, Negative is in): -6

Toe (Degrees) (Specify Toe in or out):1 in

Caster angle (Degrees):10

Kick-up (mm): stock

Sway Bar (yes/no):no

Ride Height (mm): 6mm

Springs (indicate type, length, hardness, etc): MST aluminum threaded with alumin spring stays

Damper Oil (indicate weight or #):30w

Upper Damper Position (Lower # indicates inner most position): 2

Lower Damper Position (Lower # indicates inner most position):1

Other (Weights, Mods, etc): aluminum steering assembly



Rear Setup

Camber (Degrees) (Positive is out, Negative is in): -4

Toe (Degrees) (Specify Toe in or out): 4 ish out

Caster (Degrees):10

Kick-up (mm): stick

Sway Bar (yes/no):no

Ride Height (mm): 5mm

Springs (indicate type, length, hardness, etc):Stock

Damper Oil (indicate weight or #): 30

Upper Damper Position (Lower # indicates inner most position):2

Lower Damper Position (Lower # indicates inner most position):2

Other (Weights, Mods, etc):

Drivetrain

Front Belt (mm or teeth):228mm

Rear Belt (mm or teeth)Confusedtock

Front Pulley (teeth and differential type):36t fow

Front Center Pulley (teeth and differential type):18t

Rear Center Pulley (teeth and differential type):18t

Rear Pulley (teeth and differential type):36t aluminum spool



Gearing

Spur (teeth and pitch):90t 64p

Pinion (teeth and pitch): 23t 64p (about to put on 16t)
(This post was last modified: 02-14-2015, 01:48 AM by TraneDrift.)



Users browsing this thread: 1 Guest(s)