RC Drift Chassis Information
Manufacturer:MST
Model:MS01D
Track Surfaceolished Concrete/Carpet
Tires:Competition Series F2/Spice 011
Motor and ESC:Speed Passion Sensored 10.5T/Hobbywing 60Amp Xerun
Servo:Savox 1251MG
Chassis Settings
Front Setup
Camber (Degrees) (Positive is out, Negative is in):-10
Toe (Degrees) (Specify Toe in or out):0
Caster angle (Degrees):14
Kick-up (mm): 0
Sway Bar (yes/no): No
Ride Height (mm): 10mm
Springs (indicate type, length, hardness, etc):30mm blue soft
Damper Oil (indicate weight or #): Team Losi #25
Upper Damper Position (Lower # indicates inner most position):Closest hole to center
Lower Damper Position (Lower # indicates inner most position):Furthest hole from centre
Other (Weights, Mods, etc): Front one way
Rear Setup
Camber (Degrees) (Positive is out, Negative is in):-5
Toe (Degrees) (Specify Toe in or out):0
Caster (Degrees): 0
Kick-up (mm): 0
Sway Bar (yes/no): No
Ride Height (mm): 10mm
Springs (indicate type, length, hardness, etc):Street Jam Progressive, 29.5mm, Soft
Damper Oil (indicate weight or #): Team Losi #25
Upper Damper Position (Lower # indicates inner most position): Center of optional holes
Lower Damper Position (Lower # indicates inner most position): Furthest from centre
Other (Weights, Mods, etc): Spool
Drivetrain
Front Belt (mm or teeth):Standard
Rear Belt (mm or teeth): Standard
Front Pulley (teeth and differential type): 40
Front Center Pulley (teeth and differential type): 10
Rear Center Pulley (teeth and differential type):18
Rear Pulley (teeth and differential type): 28
Gearing
Spur (teeth and pitch): 88
Pinion (teeth and pitch):22
I have only had this chassis about 2 weeks and I'm loving it. I have plans to up the cs ratio to 2.7 but it's good for now. I'll eventually get the bling bits (carbon and alloy) but I'm in no real hurry. I have real bad chatter at full lock after installing the steering crank from the vip model, so I'm now waiting on the 60 degree pro CVD's.
(This post was last modified: 03-21-2013, 09:23 PM by femur.)
Manufacturer:MST
Model:MS01D
Track Surfaceolished Concrete/Carpet
Tires:Competition Series F2/Spice 011
Motor and ESC:Speed Passion Sensored 10.5T/Hobbywing 60Amp Xerun
Servo:Savox 1251MG
Chassis Settings
Front Setup
Camber (Degrees) (Positive is out, Negative is in):-10
Toe (Degrees) (Specify Toe in or out):0
Caster angle (Degrees):14
Kick-up (mm): 0
Sway Bar (yes/no): No
Ride Height (mm): 10mm
Springs (indicate type, length, hardness, etc):30mm blue soft
Damper Oil (indicate weight or #): Team Losi #25
Upper Damper Position (Lower # indicates inner most position):Closest hole to center
Lower Damper Position (Lower # indicates inner most position):Furthest hole from centre
Other (Weights, Mods, etc): Front one way
Rear Setup
Camber (Degrees) (Positive is out, Negative is in):-5
Toe (Degrees) (Specify Toe in or out):0
Caster (Degrees): 0
Kick-up (mm): 0
Sway Bar (yes/no): No
Ride Height (mm): 10mm
Springs (indicate type, length, hardness, etc):Street Jam Progressive, 29.5mm, Soft
Damper Oil (indicate weight or #): Team Losi #25
Upper Damper Position (Lower # indicates inner most position): Center of optional holes
Lower Damper Position (Lower # indicates inner most position): Furthest from centre
Other (Weights, Mods, etc): Spool
Drivetrain
Front Belt (mm or teeth):Standard
Rear Belt (mm or teeth): Standard
Front Pulley (teeth and differential type): 40
Front Center Pulley (teeth and differential type): 10
Rear Center Pulley (teeth and differential type):18
Rear Pulley (teeth and differential type): 28
Gearing
Spur (teeth and pitch): 88
Pinion (teeth and pitch):22
I have only had this chassis about 2 weeks and I'm loving it. I have plans to up the cs ratio to 2.7 but it's good for now. I'll eventually get the bling bits (carbon and alloy) but I'm in no real hurry. I have real bad chatter at full lock after installing the steering crank from the vip model, so I'm now waiting on the 60 degree pro CVD's.