Chassis introduction:This is still a WIP setup.i have changed the gearing for cs by underdriving the front and reducing the rear overdrive.i believe that the car will be very different to me now.a little test on tiles showed very tail happy results.i will see how it goes on asphalt.
RC Drift Chassis Information
Manufacturer:Team Associated
Model:TC5R
Track Surface:parking lots asphault
Tires:hpi t-drifts,fastrax drift tires,r2-hobbies hard
Motor and ESC:Associated brushed esc for T4.1 with lipo cut-off-Etronix 17-turn brushed motor
Servo:Savox 1251-low profile
Chassis Settings
Front Setup
Camber (Degrees) (Positive is out, Negative is in):3
Toe (Degrees) (Specify Toe in or out):2 toe out
Caster angle (Degrees):tc6 6 degree caste hub
Kick-up (mm):full-suspension blocks 1a-3b
Sway Bar (yes/no):no
Ride Height (mm):3mm
Springs (indicate type, length, hardness, etc):Hpi blue soft 14.8lbs-27mm
Damper Oil (indicate weight or #):Associated 30wt-piston #3
Upper Damper Position (Lower # indicates inner most position):custom
Lower Damper Position (Lower # indicates inner most position):custom vertical
Other (Weights, Mods, etc):TC6 steering blocks,Yokomo tc-bd5 one-way unit,Yokomo drb 44mm driveshafts,hpi sprint2 wheel hubs,TC6 caster blocks
Rear Setup
Camber (Degrees) (Positive is out, Negative is in):3
Toe (Degrees) (Specify Toe in or out):0
Caster (Degrees):0
Kick-up (mm):1d anti-squat (2a-3a)
Sway Bar (yes/no):no
Ride Height (mm):8mm
Springs (indicate type, length, hardness, etc):Asso silver 14lbs
Damper Oil (indicate weight or #):30wt
Upper Damper Position (Lower # indicates inner most position):custom-vertical
Lower Damper Position (Lower # indicates inner most position):custom-vertical
Other (Weights, Mods, etc):custom made spool with 16t pulley
Drivetrain
Front Belt (mm or teeth):hpi sprint2 front belt
Rear Belt (mm or teeth)tock with tensioner
Front Pulley (teeth and differential type):40t yokomo oneway
Front Center Pulley (teeth and differential type):15t sprint2
Rear Center Pulley (teeth and differential type)tock 20t
Rear Pulley (teeth and differential type)print2 32t gear diff pulley modified to fit
Gearing
Spur (teeth and pitch):associated stock 87t 48p
Pinion (teeth and pitch): 21t 48p
(This post was last modified: 08-17-2013, 09:52 PM by STEVETC5R.)
RC Drift Chassis Information
Manufacturer:Team Associated
Model:TC5R
Track Surface:parking lots asphault
Tires:hpi t-drifts,fastrax drift tires,r2-hobbies hard
Motor and ESC:Associated brushed esc for T4.1 with lipo cut-off-Etronix 17-turn brushed motor
Servo:Savox 1251-low profile
Chassis Settings
Front Setup
Camber (Degrees) (Positive is out, Negative is in):3
Toe (Degrees) (Specify Toe in or out):2 toe out
Caster angle (Degrees):tc6 6 degree caste hub
Kick-up (mm):full-suspension blocks 1a-3b
Sway Bar (yes/no):no
Ride Height (mm):3mm
Springs (indicate type, length, hardness, etc):Hpi blue soft 14.8lbs-27mm
Damper Oil (indicate weight or #):Associated 30wt-piston #3
Upper Damper Position (Lower # indicates inner most position):custom
Lower Damper Position (Lower # indicates inner most position):custom vertical
Other (Weights, Mods, etc):TC6 steering blocks,Yokomo tc-bd5 one-way unit,Yokomo drb 44mm driveshafts,hpi sprint2 wheel hubs,TC6 caster blocks
Rear Setup
Camber (Degrees) (Positive is out, Negative is in):3
Toe (Degrees) (Specify Toe in or out):0
Caster (Degrees):0
Kick-up (mm):1d anti-squat (2a-3a)
Sway Bar (yes/no):no
Ride Height (mm):8mm
Springs (indicate type, length, hardness, etc):Asso silver 14lbs
Damper Oil (indicate weight or #):30wt
Upper Damper Position (Lower # indicates inner most position):custom-vertical
Lower Damper Position (Lower # indicates inner most position):custom-vertical
Other (Weights, Mods, etc):custom made spool with 16t pulley
Drivetrain
Front Belt (mm or teeth):hpi sprint2 front belt
Rear Belt (mm or teeth)tock with tensioner
Front Pulley (teeth and differential type):40t yokomo oneway
Front Center Pulley (teeth and differential type):15t sprint2
Rear Center Pulley (teeth and differential type)tock 20t
Rear Pulley (teeth and differential type)print2 32t gear diff pulley modified to fit
Gearing
Spur (teeth and pitch):associated stock 87t 48p
Pinion (teeth and pitch): 21t 48p