Gyro help

HRO148
Junior Member

03-29-2017, 02:29 AM

Hey guys I have a rwd sprint 2 flux, I installed a onisiki gyro and when I drive straight the wheels go crazy like it can't decide to go left or right. I'm running a savox Sc 1251 mg. I even tried a futaba bls451 and it was worse it did it when the car wasn't moving. Also I noticed that the servo only goes crazy when connected to the steering, it seems to react normal (I'm just looking at the steering horn move) when disconnected from steering. Thanks in advance

HRO148

03-29-2017, 02:29 AM #1

littlemonsta
Member

220

03-29-2017, 03:54 PM

Turn down gain until wheels don't shake. Is ch3 connected?

Sent from my Lenovo P1a42 using Tapatalk

Team Magic - E4D(4) RWD - Sakura D4 RWD

littlemonsta

03-29-2017, 03:54 PM #2

Turn down gain until wheels don't shake. Is ch3 connected?

Sent from my Lenovo P1a42 using Tapatalk

Team Magic - E4D(4) RWD - Sakura D4 RWD

HRO148
Junior Member

03-30-2017, 12:39 AM

That didn't work, and I tuned it down low. ch 3 is plugged in.

This post was last modified: 03-30-2017, 12:40 AM by HRO148.

HRO148

03-30-2017, 12:39 AM #3

That didn't work, and I tuned it down low. ch 3 is plugged in.

littlemonsta
Member

220

03-30-2017, 02:05 AM

Have you turned down gyro gain from controller ? If that doesn't work. Unplug ch3 and try manually setting gain from gyro. Where is the gyro located?

Sent from my Lenovo P1a42 using Tapatalk

Team Magic - E4D(4) RWD - Sakura D4 RWD

littlemonsta

03-30-2017, 02:05 AM #4

Have you turned down gyro gain from controller ? If that doesn't work. Unplug ch3 and try manually setting gain from gyro. Where is the gyro located?

Sent from my Lenovo P1a42 using Tapatalk

Team Magic - E4D(4) RWD - Sakura D4 RWD

HRO148
Junior Member

03-30-2017, 03:16 AM

Yeah gain turned down from control. I will try unplugging ch 3 and using manual adjustment. The gyroonwas in the middle then i moved it just behinf the steering bell cranks

HRO148

03-30-2017, 03:16 AM #5

Yeah gain turned down from control. I will try unplugging ch 3 and using manual adjustment. The gyroonwas in the middle then i moved it just behinf the steering bell cranks

littlemonsta
Member

220

03-30-2017, 05:09 AM

I'm not sure what remote you are using. Usually remotes with ch3 turn knob binded will set value from -100 to 100. So if you set it at one end of knob, gyro will be max. At the other end it will be max too.

Try to put gyro on lower chassis towards the middle to rear of chassis.

Sent from my Lenovo P1a42 using Tapatalk

Team Magic - E4D(4) RWD - Sakura D4 RWD

littlemonsta

03-30-2017, 05:09 AM #6

Team Magic - E4D(4) RWD - Sakura D4 RWD

HRO148
Junior Member

03-30-2017, 02:58 PM

Sorry, i was trying to say that the position of the gyro on the chasis was in the middle of the chasis, then i moved it closer to the front. I haven't manually adjusted the gain yet. I will try that today as well as putting the gyro lower on the chasis. Thanks for helping

HRO148

03-30-2017, 02:58 PM #7

Users browsing this thread:
1 Guest(s)