DriftMission RC Drifting Forums Chassis, Styles, and Product Discussions Option Parts Eagle Shaft

Eagle Shaft

Eagle Shaft

neortic
Junior Member
20
05-05-2014, 07:38 PM
#1
Hello

This weekend I participated in a round of a championship.

My father broke a shaft on its TT01 V3 and a friend also broke two shaft in an another TT01 V3


Anyone know where find 44mm shaft that could replaced the eagle racing? I heard there were beefier

Thank you in advance
neortic
05-05-2014, 07:38 PM #1

Hello

This weekend I participated in a round of a championship.

My father broke a shaft on its TT01 V3 and a friend also broke two shaft in an another TT01 V3


Anyone know where find 44mm shaft that could replaced the eagle racing? I heard there were beefier

Thank you in advance

lougc8
Tamiya fanboy
1,096
05-05-2014, 08:10 PM
#2
any 44mm ones for ota-r31 will fit, but the eagle ones are made thinner to give higher steering angle. Couple of things to prevent them breaking again are to have them properly greased and make sure to setup the steering epa. There's a limit to how far they can turn and will break.

[Image: 4028172207455215s.jpg]
Overdose Drift Package RWD
CER D08 Premium RWD
Yokomo DRB Overdose RWD
Ce-RX type R White Wolf RWD
lougc8
05-05-2014, 08:10 PM #2

any 44mm ones for ota-r31 will fit, but the eagle ones are made thinner to give higher steering angle. Couple of things to prevent them breaking again are to have them properly greased and make sure to setup the steering epa. There's a limit to how far they can turn and will break.


[Image: 4028172207455215s.jpg]
Overdose Drift Package RWD
CER D08 Premium RWD
Yokomo DRB Overdose RWD
Ce-RX type R White Wolf RWD

tamiya
Senior Member
531
05-06-2014, 03:34 AM
#3
is he talking about unis for TT01 or R31?

[Image: MRCsig.gif]
tamiya
05-06-2014, 03:34 AM #3

is he talking about unis for TT01 or R31?


[Image: MRCsig.gif]

lougc8
Tamiya fanboy
1,096
05-06-2014, 03:52 AM
#4
the eagle racing tt01v3 uses r31 suspension. The shafts are rated to go past 55 degrees. Like most shafts that go past 55-60 you need do proper maintenance since they are thinner and susceptible to breaking. A friend even managed to break a 60 degree mst shaft during one session. I'm using the v3 tt01 suspension on the fronts now with the same universal shafts and set my steering setup right before it is at its limit where it shakes and chatter.
This post was last modified: 05-06-2014, 03:54 AM by lougc8.

[Image: 4028172207455215s.jpg]
Overdose Drift Package RWD
CER D08 Premium RWD
Yokomo DRB Overdose RWD
Ce-RX type R White Wolf RWD
lougc8
05-06-2014, 03:52 AM #4

the eagle racing tt01v3 uses r31 suspension. The shafts are rated to go past 55 degrees. Like most shafts that go past 55-60 you need do proper maintenance since they are thinner and susceptible to breaking. A friend even managed to break a 60 degree mst shaft during one session. I'm using the v3 tt01 suspension on the fronts now with the same universal shafts and set my steering setup right before it is at its limit where it shakes and chatter.


[Image: 4028172207455215s.jpg]
Overdose Drift Package RWD
CER D08 Premium RWD
Yokomo DRB Overdose RWD
Ce-RX type R White Wolf RWD

tamiya
Senior Member
531
05-06-2014, 04:27 AM
#5
Ah ok

also when measuring angle CVDs suffer thru, it's steering angle + camber angle

[Image: MRCsig.gif]
tamiya
05-06-2014, 04:27 AM #5

Ah ok

also when measuring angle CVDs suffer thru, it's steering angle + camber angle


[Image: MRCsig.gif]

neortic
Junior Member
20
05-07-2014, 06:30 AM
#6
Thank you very much, I think I'll recommend eagle racing suddenly


Riding with a V3 TT01? You have your set up?
neortic
05-07-2014, 06:30 AM #6

Thank you very much, I think I'll recommend eagle racing suddenly


Riding with a V3 TT01? You have your set up?

Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)